![\"DSC_9946\"](\"https:\/\/setsail.com\/wp-content\/uploads\/2014\/04\/DSC_99461.jpg\")
<\/p>\n<\/p>\n
Last week we worked with Peter Watson aboard the FPB 64 Grey Wolf<\/em> to resolve a stabilizer system issue. We thought the communications regarding this might be of interest since these things do occasionally occur \u2013 typically somewhere far from home base. Have developed a problem with stabilizer on Starboard side and returning to Tahiti to effect repairs. Steve Dashew to Peter: Peter back to Steve: Saturday midday message from Steve Dashew to Don Redding at NAIAD Dynamics:<\/b><\/p>\n Hi Don, Message from Steve Dashew to Grey Wolf:<\/i><\/b><\/p>\n That’s a new one. Have forwarded to Don Redding for advice. Saturday-More detailed info to Don Redding from Steve Dashew:<\/b><\/p>\n Have now had an Iridium call from Grey Wolf<\/i>. Starboard fin has a “tracking error” and appears to be not working. Message Grey Wolf<\/i> to Falmouth Coast Guard re change in voyage plan:<\/b><\/p>\n Falmouth Coast Guard, Message Steve Dashew to Grey Wolf<\/b> :<\/p>\n Call Don Redding to discuss- if he is out, he will call you back. Leave Iridium phone number. Saturday afternoon-Message Vic Kuzmovich at NAIAD to Steve Dashew:<\/b><\/p>\n Have them inhibit the tracking alarm instead of acknowledging it. Message from Don Redding to NAIAD team and Circa Tech:<\/b><\/p>\n I have been on the phone with Peter on board the boat. The fin is hard-over CCW (cylinder fully retracted) and unresponsive. The feedback shaft coupling seems secure. My suspicion is that the starboard servo valve has failed. There is 24vdc present to power the valve amplifier, but the current loop sensor in the valve measures open circuit. That should cause a hard-over command.<\/p>\n I have asked Peter to measure the healthy port servo resistance the same way to confirm that he is looking at the right connections in the right way. If he sees 200 ohms on the port valve, then I believe it is safe to assume that the starboard valve requires replacement.<\/p>\n I’m waiting to hear back from him now. Later Don Reddng again:<\/p>\n My suspicion about the valve was premature. He was able to measure the port valve current loop sensor as 200 ohms. When he measured starboard again, it also measured 200 ohms. The valve appears to be healthy. Saturday Aprl 12-Message Grey Wolf<\/i> to Don Redding:<\/strong><\/p>\n Thanks for all your help. Do you have any update on any more diagnostics that we should run?<\/p>\n Sunday morning April 13-Communication Don Redding to Grey Wolf:<\/i><\/b><\/p>\n Were you able to manipulate the fin back to the center position and secure it with the pin? If so, I would like to check the resistance reading between positions 1 and 3, and 1 and 2 in the actuator junction box. Make these measurements with the connecting cable to the controller removed. These pairs should read approximately 5K and 2.5K ohms respectively when the fin is centered. This will check for possible slippage of the shaft connecting the potentiometer and the fin shaft.<\/p>\n Also, check the security of each of the connections inside the junction box (tug each wire gently).<\/p>\n Also, look into the plug end of the cable you removed from the junction box. Each socket inside the connector should be just below the face of the connector — all at the same height within the connector.<\/p>\n It’s 9am here, and I’m available for at least the next four hours.<\/p>\n Peter back to Don:<\/p>\n Crew asleep at present so will check in about an hour. One thing for you is we did manage to center the fin and bolt. The control panel is now reporting that it\u2019s centered so don’t think there is anything wrong with the shaft potentiometer.<\/p>\n Later Peter again to Don:<\/p>\n Refreshed overnight: Values still to come but we were thinking of changing at the datum control module the port and starboard control plugs around to see if the fault moves, can you see any problem with this?<\/p>\n Sunday morning 1130 Washington State time-Don Redding back to Grey Wolf:<\/i><\/b><\/p>\n What you propose would be a valuable test to perform. I had thought of this earlier but rejected it as too complex and risky. There is an outside chance that you may disable the one fin that is presently operational. The upside is that it would allow us to conclusively point the finger at either the starboard electronic valve or the controller starboard channel Grey Wolf<\/i> back to Don Redding:<\/b><\/p>\n Readings are: and these would appear to be correct. Sunday 1230 PM-Don Redding back to Grey Wolf:<\/i><\/b><\/p>\n If you are willing to try, this should allow us to figure out what we need to know. Sunday 1241 \u2013 Grey Wolf<\/i> back to Don Redding:<\/b><\/p>\n OK we will go off and try this.<\/p>\n Sunday 1530 \u2013Grey Wolf <\/i>to Don Redding:<\/b><\/p>\n Just an update on what we have done, Sunday 1620- Grey Wolf<\/i> to Don Redding:<\/b><\/p>\n First of all many thanks for your help in helping us diagnose the fault on our Naiad system. It\u2019s great to know that the support from your company is so good.<\/p>\n Please can you ship to our agent in Tahiti the following using the fastest delivery means possible:<\/p>\n The replacement:<\/p>\n I do not have an account, but I am sure I can pay Dashew if this is the easiest way of resolving this.<\/p>\n Pascal, Don, Pascal Bredin Don,<\/p>\n We used Fedex for some other parts and it worked well. Comments by Steve Dashew:<\/b><\/p>\n With nine FPB 64s + plus the FPB 83 in the water and actively racking up the miles, we have had very few problems with our NAIAD stabilizer gear. Aside from known wear items, like the fin position sensor (potentiometer), and hydraulic cylinder seals (we are talking 10,000 NM plus when we talk about needing preventative maintenance), other than this valve block control issue there has only been one other relatively minor problem.<\/p>\n That we can call on technically savvy NAIAD team members on a weekend, and get this sorted out for Peter Watson and crew so that the parts are on their way Monday, speaks volumes about how customer service should work.<\/p>\n With any luck we\u2019ll have Grey Wolf<\/i> on her way to Panama by the end of the week.<\/p>\n Post Script<\/strong><\/p>\n Both Todd and Mark on the Dashew Offshore team were away last weekend which is why your correspondent was so involved. This morning Don did a recap to bring them up to speed which may put this somewhat disjointed post in context.<\/p>\n Message from Don Redding to Mark Fritzer at Dashew Offshore: <\/b><\/p>\n Hi Mark: We had them look for connection problems, check the feedback potentiometer with an ohmmeter, test the electronic servo valve for the presence of 24v power, and confirm the correct resistance reading measuring the current loop sensor in the valve. Everything checked out ok, but the fin would only go fully counterclockwise any time hydraulic pressure was applied.<\/p>\n The port fin was working normally. It will do what it can to stabilize the boat in a situation like this, but overall stabilization is compromised because the port fin is 100% occupied counteracting the runaway starboard fin.<\/p>\n The possibilities were (1) feedback failure, (2) control failure in the control module\u2019s starboard channel, or (3) failure within the electronic servo valve. Those are all the active elements involved in operating the fin actuator. The crew was willing to do some rewiring to try operating the starboard fin using the port channel in the control, and vice versa. When they did this, the problem remained with the starboard fin. That narrows it down to the valve or the feedback potentiometer, but the potentiometer seemed to measure ok. We concluded that the valve had failed in a way that we couldn\u2019t detect by simple measurements. A replacement valve is shipping out to the boat today.<\/p>\n We do offer a cable set to make swapping control channels much easier than physically rewiring. See attached photo. Part number is 7100E0054.<\/p>\n Best regards,
Saturday, April 12- Received an email from Grey Wolf<\/i> describing stabilizer problem:<\/b><\/p>\n
At 12\/04\/2014 02:48 (utc) our position was 17\u00b024.92’S 149\u00b019.90’W<\/p>\n
What is the problem? Might be able to help<\/p>\n
It\u2019s locked itself in an upright position. Alarm started going on control unit. Starboard fin locked in upright position.
At 12\/04\/2014 02:53 (utc) our position was 17\u00b024.67’S 149\u00b019.24′<\/p>\n
Any suggestions? Best to communicate direct with the boat. They are near Tahiti and this is an FPB 64.
Thanks, Steve<\/p>\n
Have you tried cycling the power?<\/p>\n
<\/span>Peter back to Steve:
Yes we have cycled the power but fin is still locked. Any help you can bring to the matter much appreciated as we have not a clue, but given an hour we will be at anchor. Is there a number I can call you on?
At 12\/04\/2014 02:57 (utc) our position was 17\u00b024.44’S 149\u00b018.66’W<\/p>\n
They acknowledge the error, it goes away, and returns. At the time this occurred it was quite rough and they were getting slammed on the starboard side.
They also had a “can bus” error but this has cleared.
They do not have the commissioning codes if this is required. Owner and some of crew are technically savvy and should be able to deal with most issues.
Note that the address for the boat is Sailmail and will not accept attachments.<\/p>\n
Just to inform you that we are safely anchored in Tahiti and effecting repair.
Many thanks for your assistance.
Peter Watson
Skipper<\/p>\n
Try INHIBITING the tracking error warning – one more key stroke. System should function if this is just momentary loss of data.
Do you know\u00a0if the fin was really not moving? Usually the error message means loss of track info – even if temporary – but fin continues to operate.
Cycle power by turning off breaker.
Determine if truly not moving.
Is there second control at fly bridge?
Could be position sensor, but usually skips over worn spot with a bang.<\/p>\n
Kind Regards,
Vic Kuzmovich
Naiad Dynamics<\/p>\n
Don<\/p>\n
Don<\/p>\n
The nine plug sockets and mating plugs on the control module are all intentionally different to prevent accidental transpositions. This “idiot-proof” design makes swapping cables cumbersome if you actually need to do it.
In order to make this swap, you would have to completely remove the eight wires from both plugs P-2 and P-9 and reassemble them. Each wire has a small socket crimped onto the end. The sockets lock into the connector shell via a small releasable tab. The operation can be accomplished with needle nose pliers and a small flat blade screwdriver. Take a closer look and we can discuss this option further.
Do you have the wiring diagrams on board?
I concur with your conclusion regarding the potentiometer shaft position and the helm display. That is good news.<\/p>\n
1&3 4870
1&2 2480<\/p>\n
We have the wiring diagrams aboard so we could with care do this check. At this point can I place an order for some test leads in case I need them in the future? (Steve, we need these for the 78.) Shall we have a go?<\/p>\n
Power off (you can do this by removing P1 from the control module). P2 is the starboard channel, P9 is port.
Pull the orange plastic top piece straight out of the plug with needle nose pliers. By “top” I mean the end opposite where the wires enter. You should now be able to see the small tabs down toward the wire-end of each sleeve. These tabs capture the sleeves into position.
Make notes of wire positions and colors on your electrical drawing. Each plug uses positions 1 thru 8 only. The wire colors and order should be the same on both plugs.
Use the small blade screwdriver to release one tab while GENTLY pulling the corresponding wire completely out through the rubber insert. Repeat until all 8 wires are out. Repeat for the other plug.
Reverse the procedure to reassemble. You should feel each sleeve click into its captured position.
Reinsert the orange plastic top piece. If it doesn’t go back in easily, one or more sleeves may not be seated exactly right. Force is not your friend here.
We should probably switch to phones once you are ready to test.<\/p>\n
We have changed the plugs over on the Datum control module, so starboard to the port outlet, port to the starboard outlet and it reports as follows:
With the electronics set to control the opposite fin that the display indicates, the helm station monitor shows the port fin, rear end downward and starboard fin centralized. This inversely shows us exactly the same thing as proper wiring. (The starboard fin is locked upward and the port fin is okay). This has indicated to us that the issue is unique to the starboard stabiliser control mechanism and not a generic system fault.
These tests have been done with the engine running and the ram connected as normal
I feel that the problem is at the fin end on the starboard side and looks like it may be hydraulic or hydraulic valves or controls at the fin, what are your thoughts and where do we go now please?<\/p>\n\n
\n
\n
\n
\n
We have had a few problems with our stabiliser system and I have asked Don to organise delivering to you some replacement parts and spares.<\/p>\n
Pascal\u2019s details are:<\/p>\n
General Manager
Tahiti-yacht services<\/p>\n
Kind regards,
Peter<\/p>\n
We had a report from the boat that the starboard fin froze in the fully counterclockwise (tail-up) position during a moderately rough passage. They were able to manipulate the fin back to center by disconnecting the cylinder from the torque arm, but all attempts to control it with the DATUM control were unsuccessful.<\/p>\n
Don<\/p>\n","protected":false},"excerpt":{"rendered":"